| | 1 | = Edgrouter at boot = |
| | 2 | Broadcast message from root@ubnt (ttyS0) (Wed Jun 1 10:35:33 2011): |
| | 3 | |
| | 4 | The system is going down for reboot NOW! |
| | 5 | INIT: Switching to runlevel: 6 |
| | 6 | INIT: SenStopping routing services...zebra...done. |
| | 7 | Removing all Quagga Routes. |
| | 8 | Stopping EdgeOS router: rl-system. |
| | 9 | Asking all remaining processes to terminate...done. |
| | 10 | All processes ended within 2 seconds....done. |
| | 11 | Stopping enhanced syslogd: rsyslogd. |
| | 12 | Mounting root read-only...done. |
| | 13 | Mounting root dev read-only...done. |
| | 14 | Will now restart. |
| | 15 | Restarting system. |
| | 16 | |
| | 17 | Looking for valid bootloader image.... |
| | 18 | Jumping to start of image at address 0xbfc80000 |
| | 19 | |
| | 20 | |
| | 21 | U-Boot 1.1.1 (UBNT Build ID: 4670715-gbd7e2d7) (Build time: May 27 2014 - 11:15:15) |
| | 22 | |
| | 23 | BIST check passed. |
| | 24 | UBNT_E100 r1:1, r2:27, f:8/135, serial #: 802AA88E4E4F |
| | 25 | MPR 13-00290-27 |
| | 26 | Core clock: 500 MHz, DDR clock: 266 MHz (532 Mhz data rate) |
| | 27 | DRAM: 512 MB |
| | 28 | Clearing DRAM....... done |
| | 29 | Flash: 8 MB |
| | 30 | Net: octeth0, octeth1, octeth2 |
| | 31 | |
| | 32 | USB: (port 0) scanning bus for devices... 1 USB Devices found |
| | 33 | scanning bus for storage devices... |
| | 34 | Device 0: Vendor: Prod.: USB DISK 2.0 Rev: PMAP |
| | 35 | Type: Removable Hard Disk |
| | 36 | Capacity: 3824.0 MB = 3.7 GB (7831552 x 512) |
| | 37 | 0 |
| | 38 | reading vmlinux.64 |
| | 39 | ........................................ |
| | 40 | |
| | 41 | 8081560 bytes read |
| | 42 | argv[2]: coremask=0x3 |
| | 43 | argv[3]: root=/dev/sda2 |
| | 44 | argv[4]: rootdelay=15 |
| | 45 | argv[5]: rw |
| | 46 | argv[6]: rootsqimg=squashfs.img |
| | 47 | argv[7]: rootsqwdir=w |
| | 48 | argv[8]: mtdparts=phys_mapped_flash:512k(boot0),512k(boot1),64k@1024k(eeprom) |
| | 49 | ELF file is 64 bit |
| | 50 | Allocating memory for ELF segment: addr: 0xffffffff81100000 (adjusted to: 0x1100000), size 0x7f2a90 |
| | 51 | Allocated memory for ELF segment: addr: 0xffffffff81100000, size 0x7f2a90 |
| | 52 | Processing PHDR 0 |
| | 53 | Loading 79a980 bytes at ffffffff81100000 |
| | 54 | Clearing 58110 bytes at ffffffff8189a980 |
| | 55 | ## Loading Linux kernel with entry point: 0xffffffff81105cd0 ... |
| | 56 | Bootloader: Done loading app on coremask: 0x3 |
| | 57 | Linux version 2.6.32.13-UBNT (ancheng@ubnt-builder2) (gcc version 4.3.3 (Cavium Networks Version: 2_0_0 build 99) ) #1 SMP Tue Jun 4 14:54:28 PDT 2013 |
| | 58 | CVMSEG size: 2 cache lines (256 bytes) |
| | 59 | Cavium Networks SDK-2.0 |
| | 60 | CPU revision is: 000d0601 (Cavium Octeon+) |
| | 61 | Checking for the multiply/shift bug... no. |
| | 62 | Checking for the daddiu bug... no. |
| | 63 | Determined physical RAM map: |
| | 64 | memory: 0000000000034000 @ 000000000186c000 (usable after init) |
| | 65 | memory: 0000000006800000 @ 0000000001900000 (usable) |
| | 66 | memory: 0000000007c00000 @ 0000000008200000 (usable) |
| | 67 | memory: 000000000fc00000 @ 0000000410000000 (usable) |
| | 68 | Wasting 350112 bytes for tracking 6252 unused pages |
| | 69 | Zone PFN ranges: |
| | 70 | DMA32 0x0000186c -> 0x00100000 |
| | 71 | Normal 0x00100000 -> 0x0041fc00 |
| | 72 | Movable zone start PFN for each node |
| | 73 | early_node_map[4] active PFN ranges |
| | 74 | 0: 0x0000186c -> 0x000018a0 |
| | 75 | 0: 0x00001900 -> 0x00008100 |
| | 76 | 0: 0x00008200 -> 0x0000fe00 |
| | 77 | 0: 0x00410000 -> 0x0041fc00 |
| | 78 | Cavium Hotplug: Available coremask 0x0 |
| | 79 | PERCPU: Embedded 10 pages/cpu @a8000000020b8000 s10624 r8192 d22144 u65536 |
| | 80 | pcpu-alloc: s10624 r8192 d22144 u65536 alloc=16*4096 |
| | 81 | pcpu-alloc: [0] 0 [0] 1 |
| | 82 | Built 1 zonelists in Zone order, mobility grouping on. Total pages: 63895 |
| | 83 | Kernel command line: bootoctlinux $loadaddr coremask=0x3 root=/dev/sda2 rootdelay=15 rw rootsqimg=squashfs.img rootsqwdir=w mtdparts=phys_mapped_flash:512k(boot0),512k(boot1),64k@1024k(eeprom) console=ttyS0,115200 |
| | 84 | PID hash table entries: 1024 (order: 1, 8192 bytes) |
| | 85 | Dentry cache hash table entries: 32768 (order: 6, 262144 bytes) |
| | 86 | Inode-cache hash table entries: 16384 (order: 5, 131072 bytes) |
| | 87 | Primary instruction cache 32kB, virtually tagged, 4 way, 64 sets, linesize 128 bytes. |
| | 88 | Primary data cache 16kB, 64-way, 2 sets, linesize 128 bytes. |
| | 89 | Memory: 483444k/491728k available (3478k kernel code, 8064k reserved, 4118k data, 208k init, 0k highmem) |
| | 90 | Hierarchical RCU implementation. |
| | 91 | NR_IRQS:152 |
| | 92 | Calibrating delay loop (skipped) preset value.. 1000.00 BogoMIPS (lpj=5000000) |
| | 93 | Security Framework initialized |
| | 94 | Mount-cache hash table entries: 256 |
| | 95 | Checking for the daddi bug... no. |
| | 96 | SMP: Booting CPU01 (CoreId 1)... |
| | 97 | CPU revision is: 000d0601 (Cavium Octeon+) |
| | 98 | Brought up 2 CPUs |
| | 99 | NET: Registered protocol family 16 |
| | 100 | bio: create slab <bio-0> at 0 |
| | 101 | SCSI subsystem initialized |
| | 102 | usbcore: registered new interface driver usbfs |
| | 103 | usbcore: registered new interface driver hub |
| | 104 | usbcore: registered new device driver usb |
| | 105 | Switching to clocksource OCTEON_CVMCOUNT |
| | 106 | NET: Registered protocol family 2 |
| | 107 | IP route cache hash table entries: 2048 (order: 2, 16384 bytes) |
| | 108 | TCP established hash table entries: 8192 (order: 5, 131072 bytes) |
| | 109 | TCP bind hash table entries: 8192 (order: 5, 131072 bytes) |
| | 110 | TCP: Hash tables configured (established 8192 bind 8192) |
| | 111 | TCP reno registered |
| | 112 | NET: Registered protocol family 1 |
| | 113 | /proc/octeon_perf: Octeon performace counter interface loaded |
| | 114 | octeon_wdt: Initial granularity 5 Sec. |
| | 115 | squashfs: version 4.0 (2009/01/31) Phillip Lougher |
| | 116 | Registering unionfs 2.5.11 (for 2.6.32.55) |
| | 117 | msgmni has been set to 944 |
| | 118 | alg: No test for stdrng (krng) |
| | 119 | io scheduler noop registered |
| | 120 | io scheduler cfq registered (default) |
| | 121 | Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled |
| | 122 | serial8250.0: ttyS0 at MMIO 0x1180000000800 (irq = 58) is a OCTEON |
| | 123 | console [ttyS0] enabled |
| | 124 | loop: module loaded |
| | 125 | ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver |
| | 126 | OcteonUSB: Detected 1 ports |
| | 127 | OcteonUSB OcteonUSB.0: Octeon Host Controller |
| | 128 | OcteonUSB OcteonUSB.0: new USB bus registered, assigned bus number 1 |
| | 129 | OcteonUSB OcteonUSB.0: irq 80, io mem 0x00000000 |
| | 130 | usb usb1: configuration #1 chosen from 1 choice |
| | 131 | hub 1-0:1.0: USB hub found |
| | 132 | hub 1-0:1.0: 1 port detected |
| | 133 | OcteonUSB: Registered HCD for port 0 on irq 80 |
| | 134 | Initializing USB Mass Storage driver... |
| | 135 | usbcore: registered new interface driver usb-storage |
| | 136 | USB Mass Storage support registered. |
| | 137 | usbcore: registered new interface driver libusual |
| | 138 | Probing USB hub... |
| | 139 | hub 1-0:1.0: USB hub found |
| | 140 | hub 1-0:1.0: 1 port detected |
| | 141 | TCP cubic registered |
| | 142 | NET: Registered protocol family 17 |
| | 143 | NET: Registered protocol family 15 |
| | 144 | L2 lock: TLB refill 256 bytes |
| | 145 | L2 lock: General exception 128 bytes |
| | 146 | L2 lock: low-level interrupt 128 bytes |
| | 147 | L2 lock: interrupt 640 bytes |
| | 148 | L2 lock: memcpy 1152 bytes |
| | 149 | Bootbus flash: Setting flash for 8MB flash at 0x1f400000 |
| | 150 | phys_mapped_flash: Found 1 x16 devices at 0x0 in 8-bit bank |
| | 151 | Amd/Fujitsu Extended Query Table at 0x0040 |
| | 152 | phys_mapped_flash: Swapping erase regions for broken CFI table. |
| | 153 | number of CFI chips: 1 |
| | 154 | cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. |
| | 155 | 3 cmdlinepart partitions found on MTD device phys_mapped_flash |
| | 156 | Creating 3 MTD partitions on "phys_mapped_flash": |
| | 157 | 0x000000000000-0x000000080000 : "boot0" |
| | 158 | 0x000000080000-0x000000100000 : "boot1" |
| | 159 | 0x000000100000-0x000000110000 : "eeprom" |
| | 160 | Waiting 15sec before mounting root device... |
| | 161 | hub 1-0:1.0: activate --> -22 |
| | 162 | usb 1-1: new high speed USB device using OcteonUSB and address 2 |
| | 163 | usb 1-1: configuration #1 chosen from 1 choice |
| | 164 | scsi0 : SCSI emulation for USB Mass Storage devices |
| | 165 | scsi 0:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 6 |
| | 166 | sd 0:0:0:0: [sda] 7831552 512-byte logical blocks: (4.00 GB/3.73 GiB) |
| | 167 | sd 0:0:0:0: [sda] Write Protect is off |
| | 168 | sd 0:0:0:0: [sda] Assuming drive cache: write through |
| | 169 | sd 0:0:0:0: [sda] Assuming drive cache: write through |
| | 170 | sda: sda1 sda2 |
| | 171 | sd 0:0:0:0: [sda] Assuming drive cache: write through |
| | 172 | sd 0:0:0:0: [sda] Attached SCSI removable disk |
| | 173 | kjournald starting. Commit interval 5 seconds |
| | 174 | EXT3 FS on sda2, internal journal |
| | 175 | EXT3-fs: mounted filesystem with writeback data mode. |
| | 176 | VFS: Mounted root (unionfs filesystem) on device 0:12. |
| | 177 | Freeing unused kernel memory: 208k freed |
| | 178 | Algorithmics/MIPS FPU Emulator v1.5 |
| | 179 | INIT: version 2.88 booting |
| | 180 | INIT: Entering runlevel: 2 |
| | 181 | Starting routing daemon: rib. |
| | 182 | Starting EdgeOS router: migrate rl-system configure. |
| | 183 | |
| | 184 | Welcome to EdgeOS ubnt ttyS0 |
| | 185 | |
| | 186 | By logging in, accessing, or using the Ubiquiti product, you |
| | 187 | acknowledge that you have read and understood the Ubiquiti |
| | 188 | License Agreement (available in the Web UI at, by default, |
| | 189 | http://192.168.1.1) and agree to be bound by its terms. |
| | 190 | |
| | 191 | ubnt login: |