# Stolen from /sbin/dhclient-script using using no /usr based binaries.
# Converts an commented list into a SEP (default space) seperated list.
make_list() {
  SEP=${2:-' '}
  oldifs="$IFS"
  IFS="
"
  list=""
  for line in $1; do
    line=${line%%[ \t#]*}
    [ -n "$line" ] && list="$list$SEP$line"
  done
  IFS=${oldifs}
  echo ${list##$SEP}
}

# No kernel dumps as we don't have a place to store them 
dumpdev="NO"			

# We are an router/gateway (wireless to be precise) running the lvrouted
# routing daemon.
gateway_enable="YES"
lvrouted_enable="YES"
lvrouted_flags="-u -s s00p3rs3kr3t -m 28"

# Takes lvrouted an small while to create reachable network nodes, make sure to
# wait on it,to saves some bootup warnings.
netwait_enable="YES"
netwait_timeout="20"
netwait_ip="8.8.8.8 172.16.4.46 172.27.129.1 172.17.14.1"


# Block the full range as smaller subnets are used for allowances, this avoids
# traffic going out (due to the default route) to unreachable parts to the
# 172.16.0.0/12 network. 
static_routes="quickstop"
route_quickstop="-net 172.16.0.0/12 127.0.0.1 -reject"

# NTP server needs working config with WL network or internet on boot
# so some warnings might pop up, but no harm
ntpdate_enable="YES"
ntpdate_flags="-b -s"
ntpd_enable="YES"
ntpd_sync_on_start="YES"
ntpd_flags="-p /var/run/ntpd.pid -f /var/db/ntp.drift"

# We need no running mail server
sendmail_enable="NONE"

# Don't let syslog accept input from other remote hosts
syslogd_enable="YES"
syslogd_flags="-s -A -c"

# Remote login without DNS checking as it might not also be functionable
# -u0 prevent sshd from making DNS requests unless the authentication mechanism
# or configuration requires it.
sshd_enable="YES"
sshd_flags="-u0"

# Watchdogd: avoid visits because of unit not reachable. If sshd is not running
# for -t seconds than reboot. This is checked evert -s seconds.
watchdogd_enable="YES"
watchdogd_flags="-t 300 -s 60 -e '/etc/rc.d/sshd status'"

# Monitoring deamons
nrpe2_enable="YES"
snmpd_enable="YES"
snmpd_flags="-Ls 1"

# HTTP(S) proxy server
tinyproxy_enable="NO"

# Make sure generated ssh keys are saved 
nanobsd_save_sshkeys_enable="YES"

# low-memory footprint DHCP and non-autoritive recursive DNS resolver
dnsmasq_enable="YES"

# Explicitly disable the memory-hungry alternatives
dhcpd_enable="NO"
dhcpd_flags="-q"
named_enable="NO"
named_chrootdir=""
named_auto_forward="YES"

# WL Captive Portal and WL Web Config Overview
thttpd_enable="YES"
http302_enable="YES"

# Hybrid setup, requires outgoing VPN Server
openvpn_enable="NO"
openvpn_if="tap"
openvpn_configfile="/usr/local/etc/openvpn/client.conf"

# Enable the firewall by default
pf_enable="YES"
pf_rules="/etc/pf.open.conf"
pf_flags=''
# Used with Proxy Configuration
#pf_rules="/etc/pf.proxy.conf"
#pf_flags="-D ext_if=vr0 -D int_if=vr1 -D publicnat={80,443}"
# Used with Node Configuration 
#pf_rules="/etc/pf.node.conf"
#pf_flags="-D captive_portal_interfaces=wlan0,wlan1"
# Used with Hybrid Configuration
#pf_rules="/etc/pf.hybrid.conf"
#pf_flags="-D ext_if=vr0 -D captive_portal_interfaces=wlan0 -D publicnat=80,443"


# Autogenerated flags are used during runtime
rc_conf_running='/etc/rc.conf.running'
if [ -r $rc_conf_running ]; then
  . $rc_conf_running
else
  : > $rc_conf_running
fi